CLEAVER FUSION SPLICER
-
Fiber Cleaver Fujikura CT-30, CT-05, CT-06
-
Fiber Optic Cleaver Sumitomo FC-6S
-
Cleaver Splicer From
SUMITOMO.FUJIKURA.INNO.ILSINTECH.FITEL.JILONG
Cleave (fiber) A cleave in an optical fiber is a deliberate,
controlled break, intended to create a perfectly flat endface, perpendicular to
the longitudinal axis of the fiber. The process of cleaving an optical fiber
forms one of the steps in the preparation for a fiber splice operation
regardless of the subsequent splice being a fusion splice or a mechanical
splice; the other steps in the preparation being those of stripping and fiber
alignment.
[1] A good cleave is required for a successful low loss splice
of an optical fiber, often it is the case that fibers spliced by identical
methods tend to have different losses, this difference can often be attributed
to the quality of their initial cleaves.
[2] The general method of cleaving involves a general strategy
known as the scribe-and-tension or scribe-and-break strategy. This strategy
involves the introduction of a small crack into the fiber and the subsequent
application of a tensile force in the vicinity of the crack that causes the
fiber to cleave Cleaving technique A general cleaving strategy that is employed
is known as the scribe-and-tension strategy or the scribe-and-break strategy.
This process involves introduction of a crack in the fiber, generally by means
of cutting tool made from a material such as diamond, sapphire, or tungsten
carbide, followed by the application of tensile stress in the vicinity of the
crack. However, the specific implementations of the cleaving vary and result in
cleaves of different qualities.
[3] Certain implementations may apply the tensile force
uniformly across the cross section of the fiber whereas others might bend the
fiber around a curved surface causing excessive tensile stress on the outside
of the bend.
[4] The introduction of the crack in the fiber may also be
generated in different ways; the crack may be introduced at a single point on
the circumference or it may be generated all along the circumference of the
fiber prior to the application of the tensile force.
[5] The circumferential introduction of the crack often
allows fibers of considerably large diameters to be cleaved while maintaining
high quality of the cleave. Tools Pen-shaped scribe (aka diamond-tip scribe or
diamond wedge scribe) looks like a ballpoint pen, but has a small wedge tip
made of diamond or other hard material. This tool is used with the
"scratch and pull" technique. First the fiber is scribed
perpendicular to its length. The fiber is then pulled, which breaks at the
scribe.
This tool requires an experienced operator to produce good
cleaves. Mechanical cleavers clamp the fiber in the correct position before a
diamond wheel or blade scribes the fiber. Then, a force is applied and the
fiber gives a nice break at the scribe. Mechanical cleavers give nicer and more
repeatable cleaves.
Multifiber cleavers are used for ribbon fiber cables See also
Stripping (fiber) Recoating Optical communication Fiber optic communications
Federal Standard 1037C
ACCESORIES ALAT TELKOM CLEAVER/MATA PISAU FUSION SPLICER SUMITOMO,FUJIKURA,INNO,ILSINTECH
SWIFT,DVP,FITEL,JILONG
- Cleaver Splicer From
SUMITOMO.FUJIKURA.INNO.ILSINTECH.FITEL.JILONG,DVP
- Cleaver Fujikura CT-06
- Cleaver Sumitomo FC-6s
Semua Barang kami
BERGARANSI RESMI dan Harga pun Relatif MURAH.
Note:
- Bebas biaya antar untuk
wilayah Tangerang, Jakarta, dan Depok
- Menerima Pengiriman
Luar Kota maupun Luar jawa
- Barang yang kami jual
NEW 100% dan bergaransi resmi selama 1th.
- Dapatkan harga miring
untuk pembelian lebih dari 2 Unit.
Kami pun menerima REPAIR
semua macam merk SPLICER dan alat TELKOM lainnya.
Kepuasan Pembeli sangat kami utamakan. Anda PUAS dengan
produk Kami..Kami SENANG dengan Anda..Ok.
Kami melayani pemesanan dari seluruh Indonesia.
Untuk ongkos kirim sangat bervariatif tergantung kota tujuan.
Pengiriman melalui JNE. J&T. TIKI dan Pos Indonesia.
Ditunjang dengan MERK-MERK yang sudah terkenal & telah
diakui keberadaanya di DUNIA SURVEY diantaranya : TEKTRONIX, AGILENT, ANRITSU,
ADVANTES, FUJIKURA, SUMITOMO, YOKOGAWA, EXPO, SUNRICE TELECOM, BIRD,
RADIANTECH, DVP, GRANDWAY, JOINTWIT, LEICA, FISHER LABS, TOPCON, NIKON,
MOTOROLA DLL.
Barang yang kami jual semua 100% Baru & BERGARANSI RESMI
1 Tahun DIJAMIN..!!! Dapatkan harga special untuk pembelian lebih dari 2 unit
barang.
Untuk pemesanan
produk yang di inginkan bisa konfirmasi melalui Telpon/ Email.
Office :
PT.DWI ARTHA MEDIA
Ruko Graha Boulevard
Blok A no.10, Gading Serpong - Kelapa Dua
Tangerang, Banten 15810 Indonesia
021-28541764
Contac Person :
Gerry Hendrawan
Wa/Tlp : 0812-1866-7879
Email :
gerryyh9@gmail.com
pfiberoptic@gmail.com
Websie : https://dwiarthamedia.co.id/
0 Komentar